Grain Handling & Milling
Grain Handling & Milling
Malt Mill
- 4400 lbs/hr (2000 Kg/hr)
- Adjustable legs
- 6 1/2″ (165mm) diameter solid steel rolls
- A single lever setting for rolls
- Rolls grooved and hardened to 60 Rockwell C Roller spacing and pressure are easily adjustable
- Large Capacity hopper c/w tramp metal magnet
- Adjustable slide gate for controlling input
- 1.75″ shafts to withstand pressure from cracking malt
- 5 HP EXPLOSION PROOF MOTOR INCLUDED
- 51″ (130 cm) long x 28″ (71 cm) wide x 51″ (130 cm) high
- Weighs 620 lbs (281 kg)
- Price includes exit adapter
- Optional 5″ inclined discharge auger available
Flex auger – unloader, boot and bearing
- Required to connect flex auger inlet to mill or grist case
- 16″ rubber boot
- Straight boot or 30 degree boot available Single-out unloader
- Flex auger anchor bearing
- Flex auger bearing assembly
350 Flex Auger to Grist Case
- Drive motor and control unit is included
- Body is rugged PVC Tubing for long service life
- Can be customized to meet most site conditions. Grist capacity up to 3000 lbs/hr (1360 kg/hr)
- Malt capacity up to 4500 lbs/hr (2041 kg/hr)
Poly Grist Case
- Polyethylene hopper for malt or grist Semi transparent for level indication
- Complete with frame, hopper and roof
- Includes floor mount kit Gross capacity of 72 cu ft
- 1440 lbs of milled grist at 20 lbs/cu ft
- 2160 lbs of unmilled malt at 30 lbs/cu ft Standard 16″ opening
- Suitable for 5 – 20 bbl systems
- 60″ diameter
- 109″ overall height
350 Flex Auger to Grist Hydrator
- Drive motor and control unit is included
- Body is rugged PVC Tubing for long service life
- Can be customized to meet most site conditions.
- Grist capacity up to 3000 lbs/hr (1360 kg/hr) Malt capacity up to 4500 lbs/hr (2041 kg/hr)
Grist Hydrator 4″ (102 mm) (C/W Thermometer)
- Ureathane flex hose above valve
- 4″ butterfly valve directly above hydrator S/S construction
- T/C connection to Mash/Lauter Tun
- T/C water inlet connection
- Sleeve for connection to grist auger
- Combines grist and water entering Mash/Lauter Tun
- 3″ (76 mm) dual scale dial thermometer installed in 1/2″ (13mm) CPLG for reading outlet temperature
- 5,000 lb/hr
- Approximate weight = 7 LB’S (3.2 kg)
Water Systems
40 BBL Hot Liquor Tank
- Design pressure: Atmospheric 4 Legs c/w adjustable Footpads.
- Shell material t304 2b s/s Cladding material t304 #4 s/s
- Interior weld finish = stain removed and brightened on a regular margin and Acid Cleaned.
- Exterior weld finish = stain removed and brightened on a regular margin.
- Cladding penetrations are stain removed and brightened on a regular margin.
- Shallow cone top, Shallow cone bottom Insulation & cladding on sides and bottom
- Top fittings: Atmospheric manway, CIP c/w 1″ (25mm) side arm & sprayball, 1″ (25mm) water inlet Side fittings: Liquid level sight tube..
- Bottom fittings: 1.5″ (38mm) Triclamp Drain, thermowell, 1.5″ (38mm) overflow.
- approximately 30% Head Space.
- Steam jackets designed to heat vessel full volume of water from 70F TO 180F in 12 hours
Hot Liquor Pump
- Stainless steel pump
- Washdown duty motor
- Includes floor mount
40 BBL Cold Liquor Tank
- (Stock Code ZCL040.CN) Design pressure: Atmospheric
- 4 Legs c/w adjustable Footpads. Shell material t304 2b s/s Cladding material t304 #4 s/s
- Interior weld finish = stain removed and brightened on a regular margin and acid cleaned.
- Exterior weld finish = stain removed and brightened on a regular margin.
- Cladding penetrations are stain removed and brightened on a regular margin.
- Shallow cone top, Shallow cone bottom
- Insulation & cladding on sides and bottom.
- Top fittings: Atmospheric manway, CIP c/w 1.5″ (38 mm) side arm & sprayball, 1.5″ (38 mm) water inlet
- Side fittings: Liquid level sight tube.
- Glycol Jacket to cool 130% of the volume from 65F to 34F in 12 hours using glycol at 28F.
- Bottom fittings: 1.5″ (38 mm) triclamp Drain, thermowell, 1.5″ (38mm) overflow.
- approximately 30% Head Space.
Cold Liquor Pump
- Stainless steel pump
- Washdown duty motor Includes floor mount
Browhouse Equipment
beer brewing system
20 BBL Lauter Tun
- Design pressure: Atmospheric,
- 4 of 4″ (100mm) Legs c/w adjustable footpads. 3/4″(19mm) thread
- Shell material t304 2b s/s, Cladding material t304 #4 s/s
- Interior weld finish = stain removed and brightened on a regular margin. Exterior weld finish = stain removed and brightened on a regular margin.
- Cladding penetrations are stain removed and brightened on a regular margin.
- Formed top head, flat bottom, Insulation on sides.
- Top fittings: Atmospheric manway, 1″ (25mm) CIP, sparge piping c/w nozzles
- VFD Controlled top mounted motor for stirring rakes.
- Side fittings: Thermowell
- Bottom fittings: Wort outlets, Wedge-wire false bottom, 1.5″(38mm) wort collection header, spent grain removal port.
- Design parameters: 12 deg Plato original gravity, 95% brewhouse
- efficiency, 77% available extract, 180 kg/sq meter plate loading. 70″ ID, 5′ SIDE
- New flat bottom design reduces under-plate volume, reduces under-dough,
- and reduces the turbidity During Vorlauf and Wort Transfers. This results in a higher brewhouse efficiency and higher yields.
- Note: Spent grain port requires 12″ knife gate valve sold separately
Lauter Tun Differential Pressure Sensor
- 2x differential pressure sensors with transmitter Readout on HMI/Brehouse control panel
- Measures diferential presssure above and below the grain bed
Magnetic Particle Sanitary Flow Meter
- Magnetic flow meter
- Sanitary Magnetic flow meter
- Size: 1.5 inch (38mm), Tri-Clamp connection Integral Signal Converter
- Supply: 120 Vac
- Indication of flow and total flow
12″ (300 mm) Knife Valve (Wheel)
- 12″ (300 mm) stainless steel knife valve
- Lauter tun spent grain bottom manway knife valve Stainless steel wetted parts
- 0-ring elastomer seal
- Large handwheel for easy operation
20 BBL Steam Kettle / Whirlpool
- Design pressure: Atmospheric
- 4 Legs c/w adjustable Footpads. Shell material t304 2b s/s
- Cladding material t304 #4 s/s
- Flat bottom cladding T304 2B s/s
- Interior weld finish = stain removed,, polished to #4 on a regular margin
- Exterior weld finish = stain removed and brightened on a regular margin.
- Cladding penetrations are stain removed and brightened on a regular margin.
- Formed conical head, shallow cone bottom.
- 1.5″(38mm) Mineral Wool Insulation on sides and bottom.
- Steam jackets for low pressure steam.
- Jackets will boil the full volume at 6% evaporation per hour.
- Top fittings: 8″(204mm) vapor vent, 1″(25mm) water inlet, condensate drain
- 18″(458m) manway, 1″(25mm) CIP
- Side fittings: whirlpool inlet, thermowell, steam jackets
- Bottom fittings: drain, wort draw-off, steam jacket
- Approximate Dimensions: 66″(1679mm) ID, 6′(1.8M) SIDE Stack sold separately
- The price includes the tank placed in a mild steel cradle for shipping.
Kettle Boil Over Sensor
- Detects over boil in the Kettle and sends signal to cut steam.
Hop Dosing Port Upgrade – Steam Kettle
- System to allow for safe additions of hops to kettle while boiling
- 4″ tri clamp hop dosing port on head of vessel
- 4″ butterfly valve, 4″ ferrule, 4″ clamp, 4″ gasket, 4″ cap
- S/S open Hopper
Work Platform
- Stainless steel construction throughout
- Handrails on stairs and platform
- Convenient working height for brewhouse vessels
- Control panel mounted on handrail
- Liquor Blending Station can be mounted on the rear hand rail.
Control Panel Mounting Bracket
- Stainless steel construction throughout, Glass Beaded Finish.
- 1.5″ tube frame holds control panel and up to 3 VFD’s
- Frame mounts to the work platform railings using tube hangers.
40 BBL Unitank
40 BBL Unitank
- Vessel working pressure: 15 PSI (1 BAR) Jacket working pressure: 29 PSI (2 BAR) Working pressures are subject to local codes
- 4 Legs c/w adjustable Footpads. Shell material t304 2b s/s, Cladding material t304 #4 s/s
- Interior weld finish = stain removed, polished on a regular margin and acid cleaned.
- Exterior weld finish = stain removed and brightened on a regular margin.
- Cladding penetrations are stain removed and brightened on a regular margin.
- Formed top head, 60 degree cone bottom Insulation sides and bottom.
- Top fittings: CIP c/w 1.5″ side arm, spray ball, 2.5″ PVRV, manway (top or side)
- Side fittings: glycol couplings, thermo-well, sample port, manway (top or side)
- Jackets are sized to cool the working volume from 65F to 34F in 24 hours using a glycol inlet temperature = 30F.
- Bottom fittings: Drain & valve, racking ferrule & valve, glycol couplings.
- Relief pressure 15 psi, Relief vacuum 1psi.
- Minimum additional head space 25%
- The price includes the tank placed in a mild steel cradle for shipping.
- Racking arm and valve.
- CIP arm end piece including gauge, ball valve, quick disconnects. PVRV valve.
40 BBL Bright Beer Tank
40 BBL Bright Beer Tank
- Vessel working pressure: 15 PSI (1 BAR) Jacket working pressure: 29 PSI (2 BAR) Working pressures are subject to local codes 4 Legs c/w adjustable Footpads.
- Shell material t304 2b s/s Cladding material t304 #4 s/s
- Interior weld finish = stain removed, polished on a regular margin and acid cleaned.
- Exterior weld finish = stain removed and brightened on a regular margin. Cladding penetrations are stain removed and brightened on a regular margin.
- Formed heads top and bottom.
- Insulation on sides and bottom.
- Top fittings: CIP c/w 1.5″ side arm and sprayball ( top sight tube,
- ball valve for top pressure, pressure gauge), 2.5″ PVRV manway (Top or side).
- Side fittings: Glycol jackets designed to cool the tank volume from 65F to 55F in 10 hours using glycol at 28F, thermowell, sample port, carbonating ferrule and stone
- Bottom fittings: 1.5″ drain c/w B/F valve Relief pressure 15 psi, Relief vacuum 1psi.
- The price includes the tank placed in a mild steel cradle for shipping. PVRV Valve.